//ANYCUBIC TRIGORILLA v1.1 MAINBOARD
#ifndef __AVR_ATmega2560__
  #error "Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif

#define BOARD_NAME         "TRIGORILLA"
#define LARGE_FLASH        true

// Misc PINs
#define BUZZER         31
#define SDPOWER            -1
#define SDSS               53
#define LED_PIN            13
#define Z_MIN_PROBE_PIN     2
#define FIL_RUNOUT_PIN     19

#ifdef OutageTest
  #define OUTAGETEST_PIN  79
  #define OUTAGECON_PIN   58
#endif

// Steppers
#define X_STEP_PIN         54
#define X_DIR_PIN          55
#define X_ENABLE_PIN       38

#define Y_STEP_PIN         60
#define Y_DIR_PIN          61
#define Y_ENABLE_PIN       56

#define Y2_STEP_PIN        36
#define Y2_DIR_PIN         34
#define Y2_ENABLE_PIN      30

#define Z_STEP_PIN         46
#define Z_DIR_PIN          48
#define Z_ENABLE_PIN       62

#define Z2_STEP_PIN        36
#define Z2_DIR_PIN         34
#define Z2_ENABLE_PIN      30

#define E0_STEP_PIN        26
#define E0_DIR_PIN         28
#define E0_ENABLE_PIN      24
//------------------------------Extruder 2
//#define E1_STEP_PIN        36
//#define E1_DIR_PIN         34
//#define E1_ENABLE_PIN      30

// EndStops
#define X_MIN_PIN           3
#define Y_MIN_PIN          42
#define Z_MIN_PIN          18

#define X_MAX_PIN          43
#define Y_MAX_PIN          -1 
#define Z_MAX_PIN          -1

// Fans
#define FAN_PIN             9
#define FAN2_PIN           44
#define CONTROLLER_FAN_PIN  7

// Heaters
#define HEATER_0_PIN       10
#define HEATER_1_PIN       45
#define HEATER_BED_PIN      8

// Temperatursensoren
#define TEMP_0_PIN         13
#define TEMP_1_PIN         15
#define TEMP_2_PIN         12
#define TEMP_BED_PIN       14

// Servos
#ifdef NUM_SERVOS
  #define SERVO0_PIN      11
  
  #if NUM_SERVOS > 1
    #define SERVO1_PIN    6
  #endif
  
  #if NUM_SERVOS > 2
    #define SERVO2_PIN    5
  #endif
  
  #if NUM_SERVOS > 3
    #define SERVO3_PIN    4
  #endif
#endif  

#if defined(ANYCUBIC_TFT_MODEL)
  #define BEEPER_PIN       31
  #define SD_DETECT_PIN    49
#endif

// LCD
#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) || defined(ANYCUBIC_TFT_MODEL)
  #define KILL_PIN        41
#else
  #define KILL_PIN        -1
#endif

#ifdef ULTRA_LCD
  #ifdef NEWPANEL
    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29
    
    #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
      #define BEEPER_PIN 31
      
      #define BTN_EN1 33
      #define BTN_EN2 33
      #define BTN_ENC 35
      
      #define SD_DETECT_PIN 49
      #elif defined(LCD_I2C_PANELOLU2)
        #define BTN_EN1 47  //reverse if the encoder turns the wrong way.
        #define BTN_EN2 43
        #define BTN_ENC 32
        #define SDSS 53
        #define SD_DETECT_PIN -1
        #define KILL_PIN 41
      #elif defined(LCD_I2C_VIKI)
        #define BTN_EN1 22  //reverse if the encoder turns the wrong way.
        #define BTN_EN2 7
        #define BTN_ENC -1
        #define SDSS 53
        #define SD_DETECT_PIN 49
      #elif defined(FULL_GRAPHIC_SMALL_PANEL)
        #define BEEPER_PIN 37

        // Pins for DOGM SPI LCD Support
        #define DOGLCD_A0  23
        #define DOGLCD_CS  27
        #define LCD_PIN_BL  25  // backlight LED on PA3

        #define KILL_PIN 41
        // GLCD features
        //#define LCD_CONTRAST 190
        // Uncomment screen orientation
        // #define LCD_SCREEN_ROT_90
        // #define LCD_SCREEN_ROT_180
        // #define LCD_SCREEN_ROT_270
        //The encoder and click button
        #define BTN_EN1 33
        #define BTN_EN2 -1
        #define BTN_ENC 35  //the click switch
        //not connected to a pin
        #define SD_DETECT_PIN 49
      #elif defined(MULTIPANEL)
        //         #define BEEPER_PIN 37
        // Pins for DOGM SPI LCD Support
        #define DOGLCD_A0  17
        #define DOGLCD_CS  16
        #define LCD_PIN_BL  23  // backlight LED on A11/D65
        #define SDSS   53

        #define KILL_PIN 64
        // GLCD features
        //#define LCD_CONTRAST 190
        // Uncomment screen orientation
        // #define LCD_SCREEN_ROT_90
        // #define LCD_SCREEN_ROT_180
        // #define LCD_SCREEN_ROT_270
        //The encoder and click button
        #define BTN_EN1 -1
        #define BTN_EN2 33
        #define BTN_ENC 35  //the click switch
        //not connected to a pin
        #define SD_DETECT_PIN 49
      #else
        //arduino pin which triggers an piezzo beeper
        #define BEEPER_PIN 31  // Beeper on AUX-4
      
      //buttons are directly attached using AUX-2
      #ifdef REPRAPWORLD_KEYPAD
        #define BTN_EN1 64 // encoder
        #define BTN_EN2 59 // encoder
        #define BTN_ENC 63 // enter button
        #define SHIFT_OUT 40 // shift register
        #define SHIFT_CLK 44 // shift register
        #define SHIFT_LD 42 // shift register
        #else
        #define BTN_EN1 37
        #define BTN_EN2 35
        #define BTN_ENC -1  //the click
      #endif
      
      #ifdef G3D_PANEL
        #define SD_DETECT_PIN 49
        #else
        #define SD_DETECT_PIN -1  // Ramps does not use this port
      #endif
      
    #endif
    
    #define LCD_PINS_RS 16
    #define LCD_PINS_ENABLE 17
    #define LCD_PINS_D4 23
    #define LCD_PINS_D5 25
    #define LCD_PINS_D6 27
    #define LCD_PINS_D7 29
    
  #endif
#endif